Biolight PLUS

biolight PLUS

biolight PLUS

Reinforced fasciculate micro-post glass fibers for coronal-radicular reconstructions.

Non-invasive
Anatomical
Reinforced
Bis-GMA-free
Affordable

Dental pratice

Root anchoring

Biolight Plus
Biolight Dual
Biolight ST

Impressing

Splints and bridges

Fast Splint Matrix

Temporary reinforcement

Personal protection equipment

Adhesives and composites

Biolight Bond DC
Biolight Core DC

Laboratory

Mobile reinforcement

ALL-ON-4 reinforcement

Splints and bridges

Fast Splint Matrix

Temporary reinforcement

Personal protection equipment

Clinical Case
Protocol
Technical Data
References
Documents/Bibliography

Figure 1: The tooth has been desobturated and bitten.

Figure 2: Blasting with alumina oxide to prepare the adhesive attachment. Drying of the cavity and then soaking with adhesive by rubbing the surfaces with a micro-applicator.

Figure 3: Preparation of Biolight Plus posts Figure 2: Blasting with alumina oxide to prepare the adhesive attachment. Drying of the cavity and then soaking with adhesive by rubbing the surfaces with a micro-applicator.

Figure 4: Placing Biolight Plus posts and adding material Figure 2: Blasting with alumina oxide to prepare the adhesive attachment. Drying of the cavity and then soaking with adhesive by rubbing the surfaces with a micro-applicator.

Figure 5: Layer curing and placement of the temporary restoration Figure 2: Blasting with alumina oxide to prepare the adhesive attachment. Drying of the cavity and then soaking with adhesive by rubbing the surfaces with a micro-applicator.

Figure 6: Control X-ray

Isolate the preparation using rubber dam

Remove gutta percha to a depth of at least 1.5 times the coronal height, using ultrasonics with a tip

Leave a 5 mm minimum apical stop

Rinse and air dry

Eliminate any humidity with paper points

Clip the template over the x-ray sensor

First measure the canal width at entry to determine the size and the apical stop

First measure the canal width at entry to determined the size of Biolight Plus multi-post

Now measure the width of the apical stop to determine how many stands must be pushed come into contact with the gutta percha

Etch all surfaces that will be bonded. Rinse and air dry

Remove any residual humidity with absorbent paper points

Apply dual-cure dentine bonding agent to the etched surfaces. Air dry and absorbent paper points

Backfill the canal beginning at the apical stop. Overfill onto theprepared coronal surfaces

Insert the sleeve into the Biolight Plus

Insert the ultra-fine tip into the sleeve

Pull the Biolight Plus multi-post to expose 2/3 of its total length

Inject the resin cement until it exudes through the sleeve exit

Push the Biolight Plus back into the sleeve, while maintaining pressure on the syringe

Let go of the Biolight and continue to inject: the biolight will eject fromthe sleeve, fully impregnated

Insert the Biolight into the canal. Do not use excessive force to push towards the apical stop

Using fine scissors, remove the sheath bu cutting across the post strands

Use a condenser to vertically push down the number ofstrands

Move the remaining strandstowards the periphery of thecanal as much as possible

Allow for complete curing of the resin cement as per manufacturer 's specifications

Light cure to complete the polymerization

Complete the core build-up as necessary

See the protocol

[ Internal Data ]

Flexural strength :

Higher than 1 000 Mpa

Retention in a RCR :

50% times higher than the retention of a Mooser post

Radiopacity (ISO 4049):

Higher than 200% A1

For more information

Biolight Plus offer: 1 blister of 5 micro-posts

4 strands, Ø 0,8 mm; 1 blister of 5 micro-posts BLUE
6 strands, Ø 1,0 mm; 1 blister of 5 micro-posts BLACK
9 strands, Ø 1,2 mm; 1 blister of 5 micro-posts YELLOW
12 strands, Ø 1,4 mm 1 blister of 5 micro-posts RED

References : 03130

1 blister of 10 micro-posts RED

4 strands, Ø 0,8 mm

References : 03112

1 box of 10 micro-posts BLUE

6 strands, Ø 1,0 mm

References : 03113

1 box of 10 micro-posts BLACK

9 strands, Ø 1,2 mm

References : 03114

1 box of 10 micro-posts YELLOW

12 strands, Ø 1,4 mm NEW PACKAGING

References : 03115

Dentoscope article

Bis GMA article

Application protocol

Instructions of use

Safety data sheet

Biolight PLUS notice

Raphaël Richert Thesis

Davide Mancino
Article

Got questions? Need any precision? Contact us: +33 4 76 07 79 57

Got questions? Need any precision? Contact us: +33 4 76 07 79 57

Medical device for dental care reserved for health professionals, not reimbursed by social security. Read carefully the instructions in the leaflet or on the label before use. FiberForce, FiberForce CST, Fast Splint Matrix, Biolight: Class IIA (CE mark issued by SGS) CE1639. CST Link: Class I (CE marking)